Belgian research institute imec has demonstrated a Ge/Si avalanche photodiode combining 100 GHz bandwidth, 1.8 A/W responsivity and 5 V operation. By improving receiver sensitivity without sacrificing speed, the device could give designers of AI data-centre optical interconnects more flexibility in managing optical link budgets. The device enabled net 400 Gbps data reception in a laboratory demonstration.
The rapid expansion of artificial intelligence infrastructure is putting new demands on data-centre networks. As systems connect more accelerators, processors and switches, the volume of information moving between computing resources continues to rise. Optical interconnects must accommodate higher data rates without a proportional increase in power consumption or system complexity.
One of the toughest design problems lies at the receiving end. A photodetector must respond to extremely rapid variations in incoming light while retaining enough sensitivity to recover a weak optical signal. Bandwidth alone is not sufficient: receiver noise, optical losses and the characteristics of the associated electronics become increasingly important as link speeds rise.
In September 2026, Leuven-based research institute imec presented a germanium/silicon (Ge/Si) avalanche photodiode (APD) with a 100 GHz bandwidth. Operating at 5 V, the device achieves a responsivity of 1.8 A/W, a measure of the electrical current produced per unit of incident optical power. In an optical-link demonstration, it enabled net data reception at 400 Gbps. According to imec, the APD improved receiver sensitivity by 3 dB compared with a conventional photodiode without internal gain.
The development is notable not simply for its speed, but for combining high bandwidth with signal multiplication inside the detector—a trade-off that has historically complicated APD design.
A conventional photodiode converts incident light into an electrical current. When a photon is absorbed in a semiconductor, it can generate an electron–hole pair; an electric field then separates the charge carriers and draws them towards the contacts. In the PIN photodiodes commonly used in optical communications, this conversion takes place without substantial internal gain. When received optical power is low, the resulting current is small and the downstream receiver electronics must work with a weak signal.
An avalanche photodiode adds a multiplication mechanism. A sufficiently strong electric field accelerates carriers, which can produce further carriers through impact ionisation. The larger current reaches the receiver amplifier before electronic noise has as much relative influence. This does not eliminate the need for a transimpedance amplifier (TIA), which converts detector current into a voltage.
Avalanche multiplication, however, introduces noise of its own. The number of additional carriers varies statistically, producing what is known as excess noise. The multiplication process also takes time, so increasing gain can reduce the speed at which the detector responds. The gain–bandwidth product is therefore a central parameter in APD engineering, alongside leakage currents, breakdown voltage and detector capacitance.
Silicon is the foundation of mainstream semiconductor manufacturing, but it absorbs light poorly at the near-infrared wavelengths widely used in optical communications. Germanium is more suitable for optical detection in these wavelength ranges, including the O- and C-bands.
Integrating germanium on a silicon-photonics platform allows photodetectors to be coupled to optical waveguides and positioned alongside modulators and other photonic components. The two materials can also perform different roles within an APD: germanium provides the absorption region, while silicon supports carrier multiplication. Separating these functions allows engineers to optimise the structure for distinct physical requirements.
A conventional arrangement is the separate absorption, charge and multiplication (SACM) architecture. It contains an absorption section, a charge-control layer that helps shape the electric field, and a separate multiplication section. Imec’s researchers reworked this structure by reducing the multiplication region to less than 100 nm and removing the distinct charge layer. The design uses deeply recessed germanium in silicon.
Thinning the multiplication region shortens carrier transit and avalanche build-up times. Imec reports that the architecture retains approximately twofold internal gain while achieving 100 GHz bandwidth at 5 V. Such thin regions also demand tight control over electric-field distribution: small changes in layer thickness, device geometry or doping may affect gain and breakdown behaviour.
The 100 GHz figure describes the detector’s electrical 3 dB bandwidth—the frequency at which its response has fallen by 3 dB relative to the low-frequency response. The data rate achieved by an optical link is a separate system-level result, determined by the modulation scheme, symbol rate, signal quality and transmitter and receiver electronics.
With multilevel formats such as four-level pulse-amplitude modulation (PAM4), each symbol can encode two bits using four amplitude levels. This increases the number of bits transmitted without an equivalent increase in symbol rate, but the reduced spacing between signal levels makes the link more vulnerable to noise and distortion.
For the system demonstration, imec paired its APD with the Ge/Si electro-absorption modulator (EAM) introduced at ECOC 2025. That C-band modulator offers bandwidth beyond 110 GHz. Together the devices enabled a net 400 Gbps optical link, which imec describes as the first demonstration at this rate using an APD receiver.
A link demonstration should not be confused with a complete commercial receiver. Its eventual performance will depend on the TIA, electrical interconnects, signal processing and error-correction architecture. imec’s announcement does not provide every measurement detail needed for a full system assessment, including a complete receiver power budget and the underlying bit-error-rate conditions. These are important considerations when many optical channels must operate continuously in parallel.
Imec also reports a 3 dB improvement in receiver sensitivity over a detector without internal multiplication. Under equivalent measurement conditions, this corresponds to receiving a given signal quality with approximately half the optical input power.
In a practical optical network, this creates additional link margin. Depending on the architecture, designers might use that margin to reduce the required laser output or tolerate greater loss in waveguides, connectors and other optical elements. For AI data centres with large numbers of links, even modest improvements per channel may be consequential.
The relationship to energy use nevertheless requires care. Better receiver sensitivity does not automatically yield an equivalent reduction in total system power consumption. Laser efficiency, receiver electronics and digital processing all contribute to the energy budget. Nor does a 5 V operating voltage, on its own, establish power consumption without information about operating current.
The APD was manufactured on imec’s 300 mm silicon-photonics platform, which is designed to accommodate a broader range of photonic components using semiconductor-industry processes. The connection between device research and a manufacturing-oriented platform could also be relevant to the development of Europe’s silicon-photonics capabilities, although substantial integration and reliability work remains.
A March 2026 paper by researchers from imec and Ghent University in the Journal of Lightwave Technology described waveguide-coupled Ge/Si APDs fabricated on 300 mm silicon-on-insulator wafers. Those devices had already demonstrated a peak bandwidth above 100 GHz. At an operating point providing 2 A/W responsivity, however, the bandwidth was 70 GHz at 7 V. The later announcement’s advance therefore lies in the combination of 100 GHz bandwidth, 1.8 A/W responsivity and 5 V operation, together with the 400 Gbps link demonstration—not in exceeding 100 GHz for the first time.
Producing high-speed APDs reproducibly remains demanding. Multiplication-layer thickness, doping profiles and the quality of the Ge/Si interface influence electric-field distribution, dark current and breakdown voltage. Integrating the detector with high-speed electronics introduces a separate set of constraints: at frequencies approaching 100 GHz, parasitic capacitance, resistance and impedance mismatches can undermine the response of the receiver as a whole.
Imec plans to extend reliability testing across a wider range of temperatures and incident optical powers, and to integrate the detector with high-speed receiver electronics. The remaining challenge is not merely to maximise the data rate of a single channel, but to maintain stable performance across large numbers of optical links and over prolonged operating periods.
imec, “imec Debuts 100 GHz Ge/Si Avalanche Photodiode (APD), Enabling Net 400 Gbps Data Reception at Just 5 V,” 21 September 2026. https://www.imec-int.com/en/press/imec-debuts-100-ghz-gesi-avalanche-photodiode-apd-enabling-net-400-gbps-data-reception-just-5
ECOC 2026, “100 GHz Ge/Si Avalanche Photodiodes Enabling Net 400 Gbps Data Reception at a Low Voltage of 5 V,” presentation Th1-C4.
Teradyne’s Titan HP combines realistic device workloads, per-device junction-temperature control and a traceable stress history,…
Following functional validation of a 22 nm FD-SOI prototype, Fraunhofer is offering a RISC-V and…
Synaptics’ Astra SR200 family combines heterogeneous Arm cores, Torq neural acceleration and package-integrated DRAM to…
Tessenderlo-Ham, Belgium, 11 November 2026 – Melexis introduces the MLX90636, the world’s smallest contactless temperature…
Hi-rel connectors and components backed by in-depth product knowledge Powell Electronics Europe, the supplier of…
Founded nine months ago, Bay is already trusted by dozens of enterprises to control AI…